Wood, metal (including mild steel, hardened steel, and stainless steel), plastic, masonry, concrete, tile (including ceramic and porcelain), stone (including marble and granite), and even glass!

What can’t it drill?

Our Bits can Drill anything that is softer than their unique Carbide, Cobalt, and Titanium tip. Which is most things. The bits will not be able to drill out the tip of diamond burr bits and some solid carbide drill bits/end mills. That said, some materials that are harder to drill than others. Porcelain tile in particular requires a very sharp drill bit to drill efficiently. We recommend purchasing our Diamond Sharpening Wheel and honing up your bit regularly if you often need to drill very hard materials.

How long do the Bits last?

It depends on what material you are planning on drilling through. The harder the material the faster the edge will dull. But, good news! They’re Guaranteed For Life! If you dull or damage a bit send it back to our shop (24 Broadcommon rd, Bristol, RI) and we sharpen/replace it for Life!

Aren't Those Just Masonry Bits?

Our bits look like a masonry bit because they were originally designed to drill rebar reinforced concrete. We found that if you can drill rebar and concrete you can drill just about anything else with the same bit. The tip is the key difference, it's not just carbide, like a regular masonry bit, it's carbide, cobalt, and titanium. The tip is designed to be more durable than a carbide tip and hold an edge like a cobalt bit. They are then braised into an armor steel shank at 2700 degrees which means that a Bad Dog Multipurpose Bit can get blue hot in an insulating material like wood without the tip separating from the shank. Finally, the armor shank is significantly more durable than the shank of a masonry bit; it's designed to flex rather than snap off in a hole.

Why is my bit not drilling?

The number one problem customers have with our drill bits is not spinning them fast enough. For our Bits to work correctly, speed is key. They must be going at a minimum of 2500 RPM. The tip has a less aggressive cutting angle than a traditional drill bit, so if you spin them at the speed you would spin a traditional drill bit they won’t make anywhere near as much progress and could appear to not be working at all. When in doubt, put our multipurpose bits in an impact gun and run them flat out. For material-specific recommendations please see our How-To pages.

Will the Bit work in my drill?

With our bits speed is critical. We recommend any drill that will spin at least 2500 RPM. Impact: Our bits come with a hex end allowing you to snap it right into your impact gun for high rpm drilling. Battery/corded drill: Put your bit into a regular battery-operated or corded drill. Just make sure the drill can reach a minimum of 2500 rpm. Drill Press: When drilling tough materials it’s best to put our Bad Dog Bit into a drill press to reach the high speeds that allow our bit to work best!

When drilling at high speeds, low melting point metals such as aluminum can bind to the tip of the bit. To keep this from happening we recommend that you apply some Bad Dog Wax before and during the job.

Sale

Bad Dog Tools

Bad Dog Stubbies - Short Cobalt Step Bit Set with Locking Extensions

SKU:

639843361049-1

MPN:
Videos:: 1181243917

Add to Cart

Options

Current Stock:

$175.00

$195.00

Quantity:

FREE SHIPPING OVER $50

60 DAY MONEY BACK GUARANTEE

LIFETIME WARRANTY

Info

SKU:639843361049-1 ,UPC:

Info

SKU:: 639843361049-1
UPC:: 639843361049
MPN:
Videos:: 1181243917

Description

Bad Dog Stubby Cobalt Step Bit Set with Locking Extensions

Some jobs don't have room for a full-size step bit. The Stubby set is built for exactly those situations: the same stepped cobalt tip as our sheet metal bits, in the shortest possible drilling profile. The quick-connect hex shank drops straight into an impact gun, cutting the setup even shorter. If it fits in the opening, you can drill it. Think torque boxes, tight engine bays, cramped duct runs anywhere you can barely get a drill in.

The set covers four size ranges so you pick the bit that fits the job. All four use the same self-centering stepped tip that walks into material without a center punch and stops clean at whatever hole size you need.

When tight turns into too far, the three included extensions lock together and lock onto the bits. Nothing rattles loose inside a duct run or a wall cavity. Stack all three for 12.5 inches of extension reach.

Features:

Cobalt construction for durability in sheet metal and ductwork
Quick-connect hex shank fits any impact gun or standard drill
Self-centering stepped tip walks in without a center punch
Stop at any step for an exact hole size every time
Four bits cover 1/8" through 3/4" across different size ranges
Locking extensions connect to each other and to the bits securely
Extensions stack to 12.5" total reach for hard-to-access locations

What's Included:

4 cobalt step bits:
- 1/8" to 3/8" (5 steps) at 1-5/8" long
- 1/8" to 1/2" (7 steps) at 1-3/4" long
- 3/16" to 5/8" (8 steps) at 2-1/8" long
- 1/4" to 3/4" (9 steps) at 2-1/4" long
Locking extensions: 2.5", 4", and 6"